Circuit Breaker & Automatic Transfer Switch
Moulded Case Circuit Breaker
Air Circuit Breaker
Miniature Circuit Breaker
Residual Current Circuit Breaker
Dual Power Automatic Transfer Switch
Motor Protection Circuit Breaker
Surge Protective Device
Relay , Contactor , Starter & Frequency Inverter
Thermal Relay
General Relay
Timer Relay
Relay Socket
Solid State Relay
Contactor
Starter
Frequency Inverter
Power Equipment and Transformer and Solar
Voltage Stabilizer
Switching Power Supply
Control Transformer
Voltage Regulator
Ups & Eps
Inverter
Power Transformer
Solar Products
Instruments
KWH Meter
Panel Meter
Shunt
Current Transformer
Multimeter
Temperature Controller
Thermocouple & Thermal Resistance
Small Ptc Heater & Small Thermostat
Compass
Indicator & Switch & Warning Products
Indicator
Pushbutton Switch
Motive Switch
Limit Switch
Micro Switch
Toggle Switch
Foot Switch
Universal Changeover Switch
Float Switch
Warning Light
Siren
Warning Bell
Fuse & Disconnector
Low Voltage Fuse
Fuse Disconnector
High Voltage Fuse
Welder & Rectifier
Welder
Rectifier
Plug & Socket & Isolating Switch & Distribution Box
Industrial Plug & Socket
Weather Protected Isolating Switch
Distribution Board
Elctrical Accessories
Terminal
Cable Tie
Clips
Cable Gland
Cabinet Lock
Others
Axial Fan
Ex Products

● Address: NO.208, Weiqi Road, Yueqing Economic Development Zone, YueQing, Zhejiang, China.

● Worktime : 24 hours online   service

● Fax:0086 577 5293 1777

● Tel:0086 577 6273 1666

Five-uses Compass

Submit Comments
*Name
Phone
*Email
Address
*Message
FunctionBoundScale ValuePrecision
Five-uses compass Type97Measure
Azimuth
6000Mil20Mil20Mil
360o1o2o
Measure pitching Angle±90o5o2.5o
Compute
distance
Scale10:12%
Measure
distance
Scale(KM)1:100000 1:500002%
Mapping Measure120mm1mmSpan0.5mm



FunctionBoundScale ValuePrecision
Five-uses compass Type80Measure Azimuth6000Mil50Mil25Mil
360o5o2.5o
Measure pitching Angle±90o5o2.5o
Compute distanceScale100:15%
Measure map distanceScale(KM)1:100000 1:500002%
Coordinate RulerLength80mm Short20mm1mmSpan0.5mm


Service Instruction for Compass
1.Service Instruction for Compass
Compass Type Y/JBZ97 is composed of coordinate rulers, mechanisms for azimuth, pitch angle (slope), map/real distances, etc. It can measure azimuth,pitch angle (slope), real/map distances and map coordinate, as well as draw simple maps based on measurements.

2.Azimuth Measuring Mechanism
It consists of magnetic needle system, azimuth dial, counter-clockwise digital azimuth dial (which would be clockwise as viewed from reflective mirror), sight port and head, etc. Full graduation of azimuth is 360° for outer circle and 6000 mil for inner circle.

Procedures to measure azimuth angles in the open is as following: first open the compass, lay the counter-clockwise digital azimuth dial flat; then turn the reflective mirror to 45", and observe the azimuth angle from the mirror. The graduation pointed by the magnetic needle“N” (north) pole is read as azimuth angle.

3.Distance Measuring Mechanism
It is a simple scaled distance measuring mechanism which measures distance by three sharp angles formed between sight port and sight head (see figures on the left). The length between the sight port and the middle sharp angle would be 10 x A if taking the length between the sharp angles on each side as A, i.e., the scale is 10:1.

Suppose the real width of B (assumed target to be measured) is 5m, and let it just sits between the sharp angles’ vertexes on each side, then the distance between the target and the measurer shuold be:10 x 5 =50m.

4.Slope Measuring Mechanism
It includes slope dial, slope pendulum and reflective mirror. The measuring range is ±90o
Hold the compass as showed in the left figure, and aim at the target through sight port and head, then the slope grade from the target to the standing point could be read from the reflective mirror.
The slope measurement could also be used to do simple level calibration.

5.Map Distance Measuring Mechanism
It is composed of rolling wheel,distance dial and pointer ,and is applicable to maps of-three different scales:1:10000, 1:50000, 1:25000.Measuring unit is kilometer.

First roll the wheel and let the pointer point to “0” , then put the compass on the map with the wheel sitting at the starting point (as shown in the left figure), and roll it along the designated route on the map until reach destination.The graduation pointed by the pointer is the map distance in kilometer.

6.Coordinate Rule
It consists of one long ruler(120mm) and two short rulers (25mm), perpendicular to each other.
Put the compass on the map with the long ruler parallel to the latitude while the short rulers parallel to the longitude (as shown in the left figure). Thus the detailed coodinate of the destination could be measured. Moreover, a simple map could be draw with a ruler, and the straight distance between two points on the map could be measured directly as:


7.Maintenance

  1. The compass must be kept away from ferromagnetic materials, high-voltage power cables and electromagnetic units either in use or in storage to avoid error or low sensitivity.

  2. The compass shoule be stored in dry environment with good ventilation to avoid mildewing.

  3. The reflective mirror and the digital azimuth dial should not be distorted of bent to avoid low accuracy.

  4. White flannel could be used to slightly wipe contaminated surface(s) to keep clean and bright.

8.Product Kit

1.a compass;2.a leather case;3.a Service Instruction book;
4.a piece of flannel5. a sile ribbon;6.a plastic bag;
7.a Certification card.

 


FunctionBoundScale ValuePrecision
Five-uses compass Type97Measure
Azimuth
6000Mil20Mil20Mil
360o1o2o
Measure pitching Angle±90o5o2.5o
Compute
distance
Scale10:12%
Measure
distance
Scale(KM)1:100000 1:500002%
Mapping Measure120mm1mmSpan0.5mm



FunctionBoundScale ValuePrecision
Five-uses compass Type80Measure Azimuth6000Mil50Mil25Mil
360o5o2.5o
Measure pitching Angle±90o5o2.5o
Compute distanceScale100:15%
Measure map distanceScale(KM)1:100000 1:500002%
Coordinate RulerLength80mm Short20mm1mmSpan0.5mm


Service Instruction for Compass
1.Service Instruction for Compass
Compass Type Y/JBZ97 is composed of coordinate rulers, mechanisms for azimuth, pitch angle (slope), map/real distances, etc. It can measure azimuth,pitch angle (slope), real/map distances and map coordinate, as well as draw simple maps based on measurements.

2.Azimuth Measuring Mechanism
It consists of magnetic needle system, azimuth dial, counter-clockwise digital azimuth dial (which would be clockwise as viewed from reflective mirror), sight port and head, etc. Full graduation of azimuth is 360° for outer circle and 6000 mil for inner circle.

Procedures to measure azimuth angles in the open is as following: first open the compass, lay the counter-clockwise digital azimuth dial flat; then turn the reflective mirror to 45", and observe the azimuth angle from the mirror. The graduation pointed by the magnetic needle“N” (north) pole is read as azimuth angle.

3.Distance Measuring Mechanism
It is a simple scaled distance measuring mechanism which measures distance by three sharp angles formed between sight port and sight head (see figures on the left). The length between the sight port and the middle sharp angle would be 10 x A if taking the length between the sharp angles on each side as A, i.e., the scale is 10:1.

Suppose the real width of B (assumed target to be measured) is 5m, and let it just sits between the sharp angles’ vertexes on each side, then the distance between the target and the measurer shuold be:10 x 5 =50m.

4.Slope Measuring Mechanism
It includes slope dial, slope pendulum and reflective mirror. The measuring range is ±90o
Hold the compass as showed in the left figure, and aim at the target through sight port and head, then the slope grade from the target to the standing point could be read from the reflective mirror.
The slope measurement could also be used to do simple level calibration.

5.Map Distance Measuring Mechanism
It is composed of rolling wheel,distance dial and pointer ,and is applicable to maps of-three different scales:1:10000, 1:50000, 1:25000.Measuring unit is kilometer.

First roll the wheel and let the pointer point to “0” , then put the compass on the map with the wheel sitting at the starting point (as shown in the left figure), and roll it along the designated route on the map until reach destination.The graduation pointed by the pointer is the map distance in kilometer.

6.Coordinate Rule
It consists of one long ruler(120mm) and two short rulers (25mm), perpendicular to each other.
Put the compass on the map with the long ruler parallel to the latitude while the short rulers parallel to the longitude (as shown in the left figure). Thus the detailed coodinate of the destination could be measured. Moreover, a simple map could be draw with a ruler, and the straight distance between two points on the map could be measured directly as:


7.Maintenance

  1. The compass must be kept away from ferromagnetic materials, high-voltage power cables and electromagnetic units either in use or in storage to avoid error or low sensitivity.

  2. The compass shoule be stored in dry environment with good ventilation to avoid mildewing.

  3. The reflective mirror and the digital azimuth dial should not be distorted of bent to avoid low accuracy.

  4. White flannel could be used to slightly wipe contaminated surface(s) to keep clean and bright.

8.Product Kit

1.a compass;2.a leather case;3.a Service Instruction book;
4.a piece of flannel5. a sile ribbon;6.a plastic bag;
7.a Certification card.